Survodutide dosage chart
10 mg Vial
Survodutide is dosed at 600 mcg–6 mg weekly via subcutaneous injection in educational protocols. A 10 mg vial reconstituted with bacteriostatic water yields about 5 mg/mL. This information is for research and educational use only.
- Reconstitute
- Add 2.0 mL bacteriostatic water → 5 mg/mL (5000 mcg/mL) concentration.
- Typical weekly range
- 0.6–6.0 mg once weekly (gradual titration over 10–12 weeks).
- Easy measuring
- At 5 mg/mL, 1 unit = 0.01 mL = 50 mcg on a U‑100 insulin syringe.
- Storage
- Lyophilized: freeze at ≤−20 °C (≤−4 °F); after reconstitution, refrigerate at 2–8 °C (35.6–46.4 °F); protect from light.
- Injection frequency
- Once weekly — same day each week.
- Dosing schedule
- 1 injection per week, 7 days apart. Hold titration steps for the listed number of weeks before increasing.
Dosing Cycle & Timing
This compound follows a once-weekly schedule, not the 5 days on / 2 days off cycle used for daily peptides.
- Frequency: once weekly — one injection every 7 days.
- Pick a fixed dosing day (for example every Sunday) and keep it consistent week to week.
- If a dose day is missed, administer within 48 hours; otherwise skip it and resume the normal day.
- Do not split the weekly amount into daily doses — GLP-1 compounds have a long half-life.
- Stay at each titration step for the full number of weeks shown in the schedule table before stepping up.
Supplies needed
Plan covers the full 12-week protocol at the lowest listed starting dose: 5 mg per dose, once weekly (12 administrations in total), using 10 mg vials. After mixing with 2 mL, the concentration is 5 mg/mL and each dose requires 1 mL total.
Survodutide vials (10 mg each)
Vials are rounded up only after calculating the whole protocol: ceil(60 ÷ 10) = 6. Usable peptide remaining in an opened vial carries forward to the next dose.
- Full protocol (12 weeks)
- 6 vials (60 mg needed ÷ 10 mg)
Insulin syringes (U-100, 1 mL)
One fresh syringe per administration.
- Full protocol (12 weeks)
- 12 syringes
Bacteriostatic water (10 mL bottles)
Use 2 mL per vial for reconstitution (6 × 2 mL = 12 mL).
- Full protocol (12 weeks)
- 2 × 10 mL bottles
Alcohol swabs
One for the vial stopper per draw + one for each injection site (once weekly).
- Full protocol (12 weeks)
- 24 swabs
| Supply | Full protocol (12 weeks) |
|---|---|
| Survodutide vials (10 mg each)Vials are rounded up only after calculating the whole protocol: ceil(60 ÷ 10) = 6. Usable peptide remaining in an opened vial carries forward to the next dose. | 6 vials (60 mg needed ÷ 10 mg) |
| Insulin syringes (U-100, 1 mL)One fresh syringe per administration. | 12 syringes |
| Bacteriostatic water (10 mL bottles)Use 2 mL per vial for reconstitution (6 × 2 mL = 12 mL). | 2 × 10 mL bottles |
| Alcohol swabsOne for the vial stopper per draw + one for each injection site (once weekly). | 24 swabs |
Survodutide dosage FAQs
How much bacteriostatic water do you use to reconstitute Survodutide?
Add 2.0 mL bacteriostatic water → 5 mg/mL (5000 mcg/mL) concentration. for a 10 mg Vial vial. Add the water slowly against the inside wall of the vial and swirl — never shake — until the powder fully dissolves.
How often is Survodutide administered in research protocols?
Injection frequency: Once weekly — same day each week.
How should reconstituted Survodutide be stored?
Storage: Lyophilized: freeze at ≤−20 °C (≤−4 °F); after reconstitution, refrigerate at 2–8 °C (35.6–46.4 °F); protect from light..
How many insulin syringe units equal a Survodutide dose?
Units depend on the water volume you used. Divide your target dose by the vial concentration to get millilitres, then multiply by 100 — 1 unit on a U-100 insulin syringe is 0.01 mL. The Spartan Peptides reconstitution calculator does this conversion for you.
Is Survodutide approved for human use?
No. Survodutide is sold and referenced strictly as a research chemical. Nothing on this page is medical advice and the material is not for human consumption.
Educational and research information only. Not medical advice, not for human consumption. Values are reference figures — always verify your own math with the reconstitution calculator.
On any insulin syringe, 1 unit = 0.01 mL, so unit counts above hold across brands.