KLOW dosage chart
80 mg Vial
KLOW is a synergistic blend of peptides (GHK-Cu, BPC-157, TB-500, KPV) designed to support fat metabolism, muscle preservation, recovery, and overall body composition. Spartan Peptides protocol: mix the 80mg KLOW vial with 3mL BAC water.
- Mixing guide
- Mix 80MG KLOW with 3mL BAC water.
- Concentration
- 26.7 mg/mL blend
- Recommended dosage
- Suggested pull: 10 units
- Injection frequency
- Daily, or 5 days on / 2 days off
- Syringe
- Use an insulin syringe (U-100) for accurate dosing. 1 unit = 0.01 mL.
- Storage
- Store reconstituted vial refrigerated at 2–8 °C, protected from light. Do not freeze.
KLOW approximate breakdown at 10 units (80mg / 3mL BAC water)
| Component | Approx. per 10 units | Vial total |
|---|---|---|
| GHK-Cu | ~6.25mg | 50mg total |
| BPC-157 | ~1.25mg | 10mg total |
| TB-500 | ~1.25mg | 10mg total |
| KPV | ~1.25mg | 10mg total |
Reconstitution steps
- 1Draw 3mL of bacteriostatic water into a sterile syringe.
- 2Inject the water slowly down the inside wall of the 80MG KLOW vial.
- 3Swirl gently until fully dissolved — do not shake.
- 4Use a U-100 insulin syringe for accurate dosing.
- 5Store reconstituted solution refrigerated at 2–8 °C, protected from light.
Spartan Peptides official protocol
Amounts are approximate and based on an 80mg total blend.
- Mixing guide: mix 80MG KLOW with 3mL BAC water.
- Concentration after mixing: 26.7 mg/mL blend.
- Recommended dosage: Suggested pull: 10 units.
- Injection frequency: Daily, or 5 days on / 2 days off.
- Use an insulin syringe (U-100) for accurate dosing.
Tips to reduce stinging
Dilution example: pull 10 units → dilute with 30–40 units BAC water → let sit 30 min at room temp before injecting. Consistency is key — listen to your body.
- After drawing your dose, dilute it with an additional 30–40 units of BAC water in the syringe.
- Let the syringe sit at room temperature for about 30 minutes before injecting.
- Inject slowly.
- Glutes are preferred for less irritation.
- Make sure alcohol fully dries before injecting.
- Gentle massage after injection may help reduce sensitivity.
Reported research focus
Research purposes only. Premium quality. Built on legacy. Backed by science.
- Supports fat metabolism*
- Supports muscle preservation*
- Supports recovery*
- Supports body composition*
KLOW dosage FAQs
How do you reconstitute a 80 mg Vial vial of KLOW?
Add bacteriostatic water slowly down the inside wall of the 80 mg Vial KLOW vial, swirl gently until clear, and use the reconstitution calculator to convert your chosen water volume into syringe units.
What is a typical KLOW dose?
Recommended dosage: Suggested pull: 10 units. Figures are research reference values only.
How often is KLOW administered in research protocols?
Injection frequency: Daily, or 5 days on / 2 days off.
What concentration does reconstituted KLOW end up at?
Concentration: 26.7 mg/mL blend. On any insulin syringe 1 unit = 0.01 mL, so unit counts convert directly across brands.
What does the KLOW klow approximate breakdown at 10 units (80mg / 3ml bac water) look like?
GHK-Cu — ~6.25mg — 50mg total; BPC-157 — ~1.25mg — 10mg total; TB-500 — ~1.25mg — 10mg total; KPV — ~1.25mg — 10mg total. The full table above lists every step with matching syringe units.
What are the mixing steps for KLOW?
Draw 3mL of bacteriostatic water into a sterile syringe. Inject the water slowly down the inside wall of the 80MG KLOW vial. Swirl gently until fully dissolved — do not shake.
How should reconstituted KLOW be stored?
Storage: Store reconstituted vial refrigerated at 2–8 °C, protected from light. Do not freeze..
How many insulin syringe units equal a KLOW dose?
Units depend on the water volume you used. Divide your target dose by the vial concentration to get millilitres, then multiply by 100 — 1 unit on a U-100 insulin syringe is 0.01 mL. The Spartan Peptides reconstitution calculator does this conversion for you.
Is KLOW approved for human use?
No. KLOW is sold and referenced strictly as a research chemical. Nothing on this page is medical advice and the material is not for human consumption.
Educational and research information only. Not medical advice, not for human consumption. Values are reference figures — always verify your own math with the reconstitution calculator.
On any insulin syringe, 1 unit = 0.01 mL, so unit counts above hold across brands.